The ice maker is making ice. You can see it in the bin. But when you press the paddle on the door, nothing comes out, or you hear a grinding sound, or a few shards trickle into the glass. That's a dispenser problem, not an ice maker problem, and it's worth separating the two before anyone orders parts. Here's how to narrow it down.
Is it the ice maker or the dispenser?
Open the freezer door and look in the bin. If it's empty or nearly empty, the problem starts upstream, and our ice maker checklist is the better place to begin. If the bin is full but nothing comes out of the door, keep reading.
Step 1: Check the controls
- Control lock: many refrigerators have a lock feature that disables the dispenser. Look for a lock icon on the display and press and hold the lock button (often for a few seconds) to release it.
- Ice mode: make sure the dispenser is set to cubed or crushed, not water only.
- Door closed: the dispenser won't operate if the freezer door, or on French-door models the fresh-food doors, aren't fully closed and the door switch isn't engaged.
Step 2: Look for clumped ice
This is the most common cause by far. When ice isn't used for a while, or when the freezer warms slightly and refreezes, cubes fuse into a block. The auger, the spiral that pushes ice toward the chute, can't move it.
- Remove the ice bin. On many models, you lift it up and pull it out; check the manual.
- Break up or dump the clumped ice. Run warm water over the bin if ice is frozen to the auger, then dry it completely.
- Check that the auger turns freely by hand.
- Reinstall the bin, making sure it seats fully so the drive coupling engages.
Frequent clumping is often a sign of a freezer temperature that fluctuates, a door seal problem or simply infrequent use. If you don't use much ice, dump the bin occasionally.
Step 3: Check the chute
Look up into the dispenser chute from the door. A sliver of ice can wedge in the chute or freeze the flap shut. Gently clear it with a plastic utensil. If the chute freezes repeatedly, the flap that seals it may not be closing all the way, letting warm humid air in. On many models, a small heater keeps the chute flap from freezing; if it's failed, the flap may stick.
Step 4: Listen when you press the paddle
| What you hear | What it usually means |
|---|---|
| Nothing at all, display normal | Lock engaged, door switch, dispenser switch or control issue |
| A hum but no motion | Auger jammed by ice, or a motor struggling |
| Motor running, no ice | Bin not seated, clumped ice, or broken auger coupling |
| Clicking or grinding | Ice jam or worn auger components |
| Ice comes out but crushed won't work | Crusher blades jammed or the solenoid that switches modes |
Step 5: Check the light and water
If the dispenser light and water both work but ice doesn't, the problem is specific to the ice side: auger motor, bin or chute. If nothing on the dispenser works, look at the control board, the dispenser switch or a door switch. Electronic dispenser controls sometimes reset after the refrigerator is unplugged for a minute, but if the problem returns, a part is failing.
Models with the ice maker in the door
French-door refrigerators often have the ice maker and bin mounted in the fresh-food door or the ceiling of the fresh-food compartment rather than in the freezer. These designs depend on a well-sealed ice compartment and a dedicated cooling path. Condensation or a failing seal on the ice compartment door can lead to ice buildup and jams. Brands such as Samsung and LG use various versions of this design. Ice buildup in the compartment, water dripping from the chute or frost on the bin are all worth a service call.
Summer humidity makes it worse
Humid weather means more moisture enters every time a door opens, and that moisture can freeze around the chute flap and ice compartment. Keeping doors closed, making sure seals are clean and replacing a worn chute flap all help.
When to call for service
If you've cleared clumped ice, confirmed the lock is off, checked the doors and the auger turns freely, but the dispenser still won't work, a part has likely failed: auger motor, dispenser switch, door switch, solenoid or control board. Our ice maker and dispenser repair page covers those parts. If the bigger issue is a refrigerator that isn't holding temperature, see our refrigerator service page.
