Laundry machines show up on resale listings constantly, especially around moving season when Ohio State students head out and new homeowners upgrade. Many of those machines have years of service left. Some are being sold because they have a problem the owner would rather not mention. You can tell most of the difference in fifteen minutes if you can watch both machines run.
Before you go
- Ask for the model numbers and look them up. Confirm the dimensions fit your space and check the CPSC recall database.
- Ask whether the dryer is electric or gas. Electric dryers need a 240-volt outlet; gas dryers need a gas line and a standard outlet. Make sure your home has the right hookup.
- Ask the seller to keep both machines connected so you can run them. If they're already unhooked in a garage, adjust your expectations and your offer.
Washer inspection
Look first
Open the lid or door. On a front-loader, pull back the rubber door boot and look in the folds for tears, mold or debris. On a top-loader, look under the lid for rust spots where the finish has chipped. Check the floor under the machine for water stains, and look at the hoses: bulging, cracked or brittle rubber should be replaced regardless.
Spin the drum by hand
With the machine off, turn the drum. It should move smoothly and quietly. Grab the top of a front-load drum and push it up and down; a lot of play or a clunk can point to worn bearings or suspension. Bearing replacement is a significant repair on many front-loaders.
Run a short cycle
Choose a quick wash or rinse-and-spin. Watch for these things:
- Water enters steadily without a loud hammering sound.
- The drum agitates or tumbles without grinding.
- The washer drains completely; the drum shouldn't hold water at the end.
- The spin reaches speed without violent shaking. Some movement is normal; walking across the floor is not.
- No error codes appear on the display.
- No water appears under the machine when the cycle ends.
Dryer inspection
A dryer's three jobs are tumbling, heating and moving air. Test all three.
| Test | Pass | Concern |
|---|---|---|
| Start a timed dry for 10 minutes | Drum turns smoothly and quietly | Squealing, thumping or scraping, which can point to rollers, belts or idler pulleys |
| Open the door after 5 minutes | Noticeable warmth inside the drum | No heat at all |
| Feel the exhaust at the vent or the back | Strong warm airflow | Weak air, suggesting a clogged blower or duct |
| Pull the lint screen | Screen intact, housing reasonably clean | Torn screen, heavy lint packed in the trap |
| Open the door mid-cycle | Dryer stops immediately | Drum keeps turning |
For gas dryers, listen for the burner to light within a minute or two of starting and look through the small viewing port if there is one. Any smell of gas other than a faint whiff at the very first ignition is a reason to stop. Moving a gas dryer means disconnecting and reconnecting a gas line; if you aren't comfortable with that, hire someone qualified, and always leak-test the connection with soapy water rather than a flame.
Getting them home and hooked up
Front-load washers ship with transit bolts that lock the drum for moving. If the seller still has them, take them; otherwise, secure the drum as best you can and drive carefully. Never move a front-loader on its side if you can avoid it. When you install the pair:
- Use new fill hoses, ideally braided stainless.
- Replace any vinyl or thin foil dryer duct with rigid or semi-rigid metal duct, kept as short as practical.
- Level the washer so it doesn't walk.
- For stacked units, use the manufacturer's stacking kit; don't improvise.
Old houses near campus and in Linden often have narrow basement stairs and older dryer vents that weren't sized for today's dryers. Our basement laundry safety guide covers venting and outlets in more depth.
Which brands and types are easier to keep running?
Simple top-load washers with mechanical controls tend to be the easiest to repair secondhand, and parts for common brands like Maytag and Whirlpool are usually easy to source. Front-loaders save water and energy but have door seals and bearings that wear. Dryers in general are among the more repairable appliances, since belts, rollers and heating elements are standard parts.
After the purchase
If a used washer starts leaking, won't drain, or throws an error a few weeks in, a technician can tell you whether it's a pump, a valve or something more expensive. See our washer repair page for common faults, and our dryer repair page for no-heat and noise problems. Buying a used laundry pair is often a good decision; buying one without watching it run is the mistake to avoid.
